Delaware Valley Tackle

Long & Short are subjective terms and may mean something different to individuals. When designing a custom rod, I suggest a handle length based on species, technique, baits, rod length and physical stature of the angler. We then adjust +/- for personal preference. Grip diameter and style can also be chosen.

About the good work or horrible fishin'? lol

Our standard Clean/Lube/Inspect Service is $16.20 ($18-10%) + shipping Parts are 10% off retail I'm happy to provide a full quote to anyone with no obligation. Just email or pm reel make & model and what you'd like done. Mike

I'd expect the newer Curado to be a little smoother, but max casting distance should be similar. To check you need to use the same rod, line and lure to get an accurate assessment. Was the reel cleaned professionally? you may want to consider that if not. These reels respond exceptionally well to tuning also.

The Smoooth Drag Carbontex washers are the real deal, and inexpensive.

Thanks for the vote of confidence guys.We're here to help and have a 100% satisfaction guarantee. Mike

Here: http://www.mudhole.com/Shop-Our-Catalog/Handle-Kits http://www.mudhole.com/Shop-Our-Catalog/Grips

Is this what you're looking for? http://www.reelgrip.com/

x2 The same holds true for Carbon drags & ceramic bearings

Are you asking about Carbon Fiber drag washers or ceramic ball bearings?

How do you suggest I spin the bearings? Just a good spin each direction with a flick of your finger. Leaving the bearings out to dry is fine. Better to be all solvent is out than to have lube contaminated. Is it okay to leave the bearings out to dry for a day after soaking it in Acetone?

Check the bearing after the solvent has had time to fully evaporate. The solvent actually acts as lubricant at first and can mask bearing wear. J's right, it will be apparent if the bearing's bad.

I would advise against permanently bonding a 2 pc. rod. There is no performance advantage to be gained. If he ferrule is loose or damaged there are better fixes.

I'd keep the water away from bearings. Whichever solvent you choose to use, there is no need to mix & match. Spin the bearings and make sure all solvent is evaporated prior to lubing.

Doubtful a reel that new needs bearings. Swapping bearings without a proper cleaning will not yield full results anyway. Have it professionally serviced and I think you'll be pleasantly surprised. If you'd like to send it in, BassResource.com Members get a 10% discount on parts & labor. Mike

Either put the line spool on a shaft with the line coming off the bottom, or lie the line spool flat on the floor and make sure the coils are coming off in the same direction it is going on the reel. If the line is twisting, flip the spool over.

Adding bearings to the handle is one way manufacturers up their bearing count. They can also be on the main gear shaft or level-wind.

There are several factors that affect the sensitivity of a rod, but spinning vs. casting isn't one of them. Blank material and weight, especially at the tip are key factors. This where micro guides come in. You can increase sensitivity of the overall rig by choosing an exposed blank reel seat, braided line and tungsten weights. The OP mentioned 1/4 oz weights specifically. My personal preference for baits in this range is med or Med. Lt. spinning tackle.

Welcome skeetercraig!

Welcome Susqy from NEPA...!

FYI - Contact us for Boca Bearings @ 10% off retail. If you are going with Orange Seal bearings and you do regular maintenance, consider running them open for max advantage. I typically recommend bearing upgrades when replacing worn out OEM parts. However, if you are an enthusiast and like to tinker, go for it. Mike

pm sent

I feel the Pflueger President compares more to the Revo S or Citica. All good reels and $68 for any of them sounds like a pretty good deal.

Easton's about 65 miles from where I live, Milford PA. We could hook up in the Watergap and hit the river or Hidden Lake or something.