Just recently one of my spinning reels began sounding like there is sand in it while I reel.  I tried cleaning it but to no avail.  I am no expert so my cleaning was removing the spool and cleaning in and around what I could.  Not opening up the guts.

 

Is my reel shot?

If you think it is worth saving send it to Mike at DVT.

 

http://www.delawarevalleytackle.com/

Not necessarily, but the more you use it as-is the harder it will be to salvage. Any chance it actually is contaminated? Doesn't have to be sand per say, dunked in dirty water, a ride down the road strapped to the boat deck, etc

It is repairable.  Send it to Delaware Valley Tackle.

 

The reel will probably need a good cleaning and some parts, especially the plastic ones that broke.

 

It will be good as new when you get it back.

What Reel? If its a 30$ reel? Toss it or take it apart, side cover... If its valuable in cost send it off, if it's a hardcore fave/ sentimental reel send it off... Hard to give a absolute answer...

The reel in question is an Abu Garcia Orra S.  I have had it for over 2 years now.  They cost between $60 - $70 bucks.

 

I don't know what one of these cleanings would even cost.  Would hate to go that route when it might be better off just replacing it.

The reel in question is an Abu Garcia Orra S. I have had it for over 2 years now. They cost between $60 - $70 bucks.

I don't know what one of these cleanings would even cost. Would hate to go that route when it might be better off just replacing it.

Exactly....

Well replace it, then take the old one apart and clean and grease it....gears get grease....lightly, bearings get oil.  Put it back together and see what happens.  

 

The reel in question is an Abu Garcia Orra S.  I have had it for over 2 years now.  They cost between $60 - $70 bucks.

 

I don't know what one of these cleanings would even cost.  Would hate to go that route when it might be better off just replacing it.

 

 

Suggest you get a new one and use the old one as practice reel for your DIY maintenance study.

It will help you understand the inner workings of the reel and gain more confidence in opening up future reels.

 

If you can get it back running you will have 2 reels on your arsenal and that is always good.

 

I did the same thing on an old baitcaster that was acting up.  I got a new one then practiced on the old one

and got her back running smoothly again (after the nth try hahaha).

The cost of reel service is $19.20 ($22-10%). If you're inclined to DIY I'll help you out if I can. 

The cost of reel service is $19.20 ($22-10%). If you're inclined to DIY I'll help you out if I can. 

 

That's pretty decent of you.  It's that kind of willingness to lend some advice and help, while not giving allowing your business to tank, that shows others you're the type that I want working on my stuff when it needs done. 

 

I'm fairly new here but I've been seeing more and more of this type of mentality from many other BassResource.com Advertisers also, I'm liking it here.

The cost of reel service is $19.20 ($22-10%). If you're inclined to DIY I'll help you out if I can. 

 

I very much appreciate it ... PM me and we can make arrangements to meet up at your facility.  You aren't too far from me.

 

If it is at all possible maybe I can learn a bit while the reel service is being done.  No pressure if it would be an inconvenience.  I am not much of a tinkerer and would rather trust in DVT to do it right.

Without seeing the reel it is hard to say but a simple clean and lube may be all that is needed. You can probably have it cleaned inspected and lubed, and if any parts are needed cover them for less than 1/2 the cost of a new one, so if you really want to keep it and be sure, let a pro do the work. If you decide it isn't worth 20 to 35 bucks, buy a new one and do what others said, carefully take it apart "with the schematic in front of you" and go thru the cleaning and inspection process, usually bad bearings and broken parts can be easily detected, and you may find it can be saved by simple clean and lube. BUT be prepared to realize even if you save it doing it yourself, most quickly discover when they do this, that those of us who do reel repair work "FAR TO CHEAP" and it is extremely cheap to have someone else spend all the time and materials to take care of your servicing hassles!! or you could be one of those that enjoy it and find it is doable themselves, if not your not out anything!! Good Luck with however you decide to tackle it.

Without seeing the reel it is hard to say but a simple clean and lube may be all that is needed. You can probably have it cleaned inspected and lubed, and if any parts are needed cover them for less than 1/2 the cost of a new one, so if you really want to keep it and be sure, let a pro do the work. If you decide it isn't worth 20 to 35 bucks, buy a new one and do what others said, carefully take it apart "with the schematic in front of you" and go thru the cleaning and inspection process, usually bad bearings and broken parts can be easily detected, and you may find it can be saved by simple clean and lube. BUT be prepared to realize even if you save it doing it yourself, most quickly discover when they do this, that those of us who do reel repair work "FAR TO CHEAP" and it is extremely cheap to have someone else spend all the time and materials to take care of your servicing hassles!! or you could be one of those that enjoy it and find it is doable themselves, if not your not out anything!! Good Luck with however you decide to tackle it.

Almost every time a customer sees what is truly involved in a full tear down service they comment that I don't charge enough. In a world where many expect something for nothing that speaks volumes. 

Little did I know that DVT was so close to me. I got Mike the reel last Tuesday and I had it back Friday morning. Put it to work yesterday and it acts like new. So awesome!!!

Thanks for such quality work!

great news...glad it all worked out.

Mike is a great guy.  i sent him my Shimano i bought here because it was "sticking" when i reeled it in.  i was like you Felix...not very sure of myself to do more than basic clean, lube and grease.  i sent it to Mike and it came back quck and works perfect...

another vote for DVT and Mike!