Jump to content
Joshua Vandamm

Where does this part fit? (Daiwa spinning reel)

Recommended Posts

Hey guys. I took my daiwa exceler 2000 HA apart for the 1st time and I can't figure out where this piece fits. 

Schematics are terrible. 

 

Please help!! ??

IMG_8968.PNG

Share this post


Link to post
Share on other sites

Bump. Hoping to use it today???‍♂️??

Share this post


Link to post
Share on other sites

Sorry I cannot help.  This is one of the reasons I let the pros do the serious service work.  Reels are so complex today that I think it good judgment to let the pros do anything that requires dis-assembly more than taking the side plates off for access to the first layer, or changing level wind pawls.  It's just too easy to screw it up.  If you're like I am.

  • Like 1

Share this post


Link to post
Share on other sites

If you took the clutch assembly apart, I think it is the spacing sleeve..

Share this post


Link to post
Share on other sites

Thanks! But I did not. I took off the bail assembly, spool, handle and side plates. 

Heres another pic for scale. Hieght about 2mm 

IMG_8995.PNG.ffe3db43cbf79b236c069f98b2f68818.PNG...height about 2mm. Pictured here 

IMG_8998.PNG

Share this post


Link to post
Share on other sites

Take a look at the attached schematic. It looks like item 65 (collar E) for the 2000HA. It goes over the black cut collar in the pic above #67(Collar F) which is on your thumb screw.

Daiwa exceller.pdf

  • Like 1

Share this post


Link to post
Share on other sites
13 minutes ago, cadman said:

Take a look at the attached schematic. It looks like item 65 (collar E) for the 2000HA. It goes over the black cut collar in the pic above #67(Collar F) which is on your thumb screw.

Daiwa exceller.pdf

I think your right!! Thanks man. Makes sense since the handle assemble is very loose now. 

Odd since it's not even on the 2000 sh schematic that came with the reel. 

 

 

Share this post


Link to post
Share on other sites

Doesn't work if fitted over the collar however. Just blocks it from going inside the shaft. Perhaps it fits somewhere behind the retainer or the pinion gear?

Starting to think it's one of the o rings...its a semi soft rubber 

Share this post


Link to post
Share on other sites

Scratch that I think I got it. Your correct @cadman I was able to force. It over the shaft actually, by placing it over the thumb collar. 

Seems to work!

Share this post


Link to post
Share on other sites

Glad it all worked out. BTW I was out of ideas after this anyway. Good Luck

  • Like 1

Share this post


Link to post
Share on other sites
On 18/7/2017 at 9:54 AM, Jvanda1 said:

Hey guys. I took my daiwa exceler 2000 HA apart for the 1st time and I can't figure out where this piece fits. 

Schematics are terrible. 

 

Please help!! ??

IMG_8968.PNG

 

:lol-045:

Share this post


Link to post
Share on other sites
12 minutes ago, Raul said:

 

:lol-045:

What's the gag? Lol

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • fishing

    bass fishing

    fishing forum

    fishing rods

    fishing rods

    fishing rods


    fishing rods

    fishing reels

    bass fish

    fishing poles

    Truck Caps

    fishing reels
    fishing reels

    fishing

    bass fish

    fish for bass
    fish

×