Robeng

I have a 1991 that I start the same way, and it also has exhibited re-start issues. When I restart, I do not prime the bulb-even an hour later. The compression is great among all four cylinders. I've replaced the oil sensing alarm and power trim (which was not cheap). New batteries for this year. Hope no issues. Though, I was looking at the starter the other day..... MikeinFresno: Does yours ever drip inside from like carbs or other areas? RingKing: Thanks for the info. Nice pics. I hear these motors are work horses and mine is already 24 years old with no major overhaul. Thanks

I purchased the MotorGuide i3 45/45 last fall and no breaker was in the box as they recommend I buy theirs or equivalent. I purchased an equivalent that mounts right to the battery post. thanks for sharing that.

I have a 1991 Mercury 40hp, 2 stroke, 4 cylinder that is oil injected. Runs fine. (do regular routine maintenance myself) If you have one, please tell me the good, the bad, the ugly. Please let me know what you have experienced; tips; tricks; parts; repairs; etc. Thanks-just curious and perhaps can be the start of exchanging thoughts among owners of same.

I also give great kudos to this forum compared to many other I have been part of or viewed regularly. Heart warming to see the generosity and everyone helps everyone. I agree, pay it forward when you can.

Thanks for the info. Great app.

I like em.

Thank you Ford. Welcome to the best, most informative, most read Bass forum. Thanks for your support.

To my knowledge you cannot. Each needs their own transducer.

Why not happy? I have the i3.

My vote is elite 5hdi combo. Good pricing right now. Make sure transducer is included.

Check other posts within electronics forum. I have elite5 hdi combo n like it. So ask away.

Reuse torn plastics as trailers or panfish baits. Reuse storage containers like from coffee.

Thanks Wayne and Fishing Rhino. Keeper of a video.

Thanks everyone.

Looking to see what everyone uses as a grease/lubricant for their trailer jack shaft and Zerk fitting for gears? I have used bearing grease on the shaft and other times even WD40 which I understand the WD40 attracts dirt, contaminants. So I dont use WD40 anymore. For past jack shafts (exterior) I have owned, I also have used Boeshield T9 for the shaft or a spray silicone. The jack also has a Zerk fitting for gears, which some say use a type of chain lube or a lithium based machine grease. Or marine grease like a Quicksilver 2-4-C with PTFE. What do you all use for the shaft and gears? Thanks in advance.

Having the Elite 5 hdi combo with transducer 83/200 & 45/800 combination for down imaging and sonar. Works great. overlay, etc. I keep sensitivity up usually and am in shallow mode as most lakes here dont go beyond 30 feet deep that I fish.

Thanks Lund Explorer- I appreciate your advice.

Nice Toads! Congrats from the north country.

That was just fantastic!! Very interestng.

Agreed with above as my 1991 40hp ELPT is very similar. Always glad to help with what I know and don't know.

I have a motorguide x3 with 45 lb thrust and 45 inch. Bow mount on 16 foot aluminum. Deep cycle battery only for it. Works well. I did a lot of research prior too. Bow mount pulls and works better in wind. Easier to pull than push. Though when excessive wind trolling motors can't keep up is my opinion. I got foot pedal which is good but sometimes think the hand operated might have been better but then you need one hand being used. Just a thought. Good luck.

Thanks to Lund Explorer, Catt, and A-Jay. Much appreciated. Lund Explorer: I have heard similar opinions I the Chene anchor. Thank you again.

I am looking for 3 strand nylon rope to tie onto fluke anchor. Rope Diameter is 3/8 x 100-150 ft long. I really only need 100ft for 16 ft aluminum Lund. Fluke anchor is a Chene anchor. Made in Michigan---some like them-some dont. Thought I'd give it a try. I also have coated fluke anchors but in certain bottom conditions, the bow doesnt always hold well in strong wind. Thought maybe the Chene anchor (non-coated) would be better off the bow. Grab bottom better. Question is >>>What brand rope? (I dont want too soft of a rope, using the 3 strand nylon. Of course, must hold tie-off directly to anchor (no chain allowed as it is a slip ring type) AND splice well.) Any suggestions of specific brand rope? Thoughts on Chene Anchor and tie-off? See pictures. Thanks in advance. Much appreciated.

I wear too as I have already had a small spot of skin cancer a few years back. Doc told me to cover up.

In the garage. I keep new SUV outside and 24 year old Lund in garage! My lady just shakes her head at me. City allows 5 days in driveway then off 5 days. Crazy rule. I have a neighbor that actually complained on the 6th day--he has nothing better to do. I live on country road not cement suburb. If you drive around area many people park them in driveways all year long. But Im good with the garage. Better for my boat. And me.