Hogsticker, how do like that Alps reel seat? I have one, but it's not on a rod just yet.

I dig it. Much more comfortable than the Acs, and made to fit my smallish hands. The double lock down nut is a nice touch.

Newest toy

I guess I'm late to the Met DC party...but at least I have line on mine...

Met DC has the same open-ended knobs as the Conquest14 - some folks like 'em, some don't:

To set up the reel - select the "OPEN" position on the external dial on the bottom of the sideplate and then thumb over the sideplate latch (located to the rear of the dial):

With the sideplate removed, select your line type from the dial visible on the top edge of the sideplate: N = nylon, F = flouro, PE = braid:

While the sideplate is off you can see the I-DC5 control module. I haven't a clue as to how to service the spool bearing that is under the module (remove the three screws perhaps):

End of spool shaft with several grooves milled in the length. The control module (when installed) extends quite a way into the recess in the spool:

Re-install the sideplate and adjust the external dial to match the weight of your bait. There are 5 positions: 1, 2, 3, 4, and A (auto):

1 = 18 - 30 grams

2 = 10 - 20 grams

3 = 8 - 12 grams

4 = 5 - 8 grams

A = 7 - 30 grams

Near as I can tell, the auto position will provide adequate braking for that wide range of baits (1/4 to 1 oz), but selection of one of the numbered brake positions will give a more optimum braking profile.

I selected position two (~ 3/8 to between 5/8 and 3/4 oz):

And the auto position:

I usually don't show my new gear until I've caught a fish with it. However, my lakes are frozen over at the moment. For now, I will just have to assume that this reel will eventually get my highest approval rating: "Seems to work, reels in fish"

Wow. Drooling over that right there!!

The new Aldebaran has landed..

Looks like it's ready for Warp 9 !

I hate being a lefty!!!!

Goose in response to your question.....While the sideplate is off you can see the I-DC5 control module. I haven't a clue as to how to service the spool bearing that is under the module (remove the three screws perhaps) That is what I do with my I-DC4 reels.

The new Aldebaran has landed..

Just ordered an HG. Was curious as to which baits and rod(s) you'll be using this reel with.

Just ordered an HG. Was curious as to which baits and rod(s) you'll be using this reel with.

I've been researching rods for it. Probably something in the 6'8 length for better balance. I'll use this for anything under 3/8ths really.

 

The boys lined up for the season

Goose in response to your question.....While the sideplate is off you can see the I-DC5 control module. I haven't a clue as to how to service the spool bearing that is under the module (remove the three screws perhaps) That is what I do with my I-DC4 reels.

Thanks! I'll check it out after I fish the reel a bit. Still have hard water here so it will be a while...

Uuuggggh I gotta wait until April for a lefty.

The Ultima is here 

 

 

My 2015 lineup, cant wait for the ice to melt !!

 

The Ultima is here 

 

 

My 2015 lineup, cant wait for the ice to melt !!

 

That is sweet!

ok JDM afficianados.....anyone know of a 3 piece JDM travel rod?  I am looking for a travel rod 7' or less with a weight range that goes up to 3 oz or so!

 

Jeff

ok JDM afficianados.....anyone know of a 3 piece JDM travel rod?  I am looking for a travel rod 7' or less with a weight range that goes up to 3 oz or so!

 

Jeff

 

Thats a tough order, you might be able to find something 2 piece

Thats a tough order, you might be able to find something 2 piece

 

 

I have found some 2 piece.  But they are too long to take as a carry-on, and I will never check another rod with an airline.  The heaviest weight rating 3 piece rod I have found so far is the Lomis escape H and the St Croix tidemaster H which are rated to 2 oz. The Escape is the right length at 6'9'' but the tidemaster is 7'6''.  Those are the 2 best options for USDM rods, so I was hoping to find something JDM.

 

Jeff

ok JDM afficianados.....anyone know of a 3 piece JDM travel rod?  I am looking for a travel rod 7' or less with a weight range that goes up to 3 oz or so!

 

Jeff

 

 

If you are ok with a 6 foot 2 piece high end rod, World Shaula 1604SS-2  (15grams to 80 grams) will do the job you want. It's designed to throw big top water for rainforest area and jigging in offshore settings. 

Sounds like loomis or St croix will be your best best. If you dont mind going a little lighter the phenix redeye looks good.

 

http://www.phenixrods.com/index.php?main_page=page&id=82

 

If you insist on a jdm rod, id look into majorcraft, evergreen, and possibly gancraft.

This rod is for Peacock in the amazon. I will check into World Shaula. And the Phenix. Thank guys. If you find anything else guys, let me know.

Jeff

I have multiple rods that have weight ranges up to 1.5 oz already. Just need something heavier! Needs to be 3 piece because airline restrictions are 33 linear inches. That is exactly how long my tube is. So if it were 2 piece, the max length would be 5'6" and I think that is too short.

Jeff

I have multiple rods that have weight ranges up to 1.5 oz already. Just need something heavier! Needs to be 3 piece because airline restrictions are 33 linear inches. That is exactly how long my tube is. So if it were 2 piece, the max length would be 5'6" and I think that is too short.

Jeff

 

Cabelas XML Travel can get you to 2 1/4oz - and, it's a 4-piece rod so it would pack very short.

Cabelas XML Travel can get you to 2 1/4oz - and, it's a 4-piece rod so it would pack very short.

 

 

Good eye.  Still looking for heavier, but that seems the heaviest option so far.  Although, I think I would opt for the Loomis escape at 2 oz, just because the length of 6'9'' would help with the topwater more than the 1/4 oz lure rating would. 

 

Thanks for all the help guys......I have been looking for a good bit and haven't found what I am looking for, and that is why I turned to y'all for the help!  keep em coming if you find one!

 

Jeff

Hope you still have a Cumulus or two in hiding! Nice rods regardless.