Bird

I use a MH for flukes with a heavy wire Gamakatsu 4/0 superline screw lock hook. The reason for spinning gear is I can't skip with casting gear 😞

Best - finesse, patients and line watching. Worst - fishing with power fisherman and loosing everything above because I'm catering to their needs 😳

I've seen so many threads about braid digging and still can't fathom it. All spinning reels have 15# braid and all baitcasters have 20# braid and never experienced it. Wish I had a solid answer but do hope you get it resolved.

I clamped a tape measure to the top of the square axle housing up against the flange on both sides. I then pulled a measurement to the square section of tounge where it folds giving a nice flat surface to deal with. I then loosened the 4 bolts holding the leaf spring assembly on just one side and tapped with a heavy rubber mallet until both measurements were equal. I did loosen the opposite side to prevent binding. Guess the 'ole saying holds true " if you want the job done right you gotta do it yourself " . Thanks for asking.

Just a little update and in case someone may face this issue. I was experiencing uneven tire wear on a single axle boat trailer and likely found the culprit today. Found the axle to be out of square by half an inch so should correct the tire wear, hopefully.

I love the 'ole time approach but.......Josh Jones ?

Guess I'm a slow learner, infact I know I am. Started years ago with the original Power Pro braid and still using it today. I was given a spool of Vicious no fade 50# 2 years ago and have yet to try it, maybe I should.

The only reason I use a fluorocarbon leader is the confidence boost. Moving baits can be thrown on a tow chain ⛓️ 😂

Jackall flickShake specific. 1/16 VMC weedless wacky head. Jackall 4.8 green pumpkin candy for clear water, cola for everything else. Thank me later

Lowe Stinger 175. The boat is relatively light being an aluminum hull and sits low to the water. The 70lb motor guide has no issues in a head wind. Bow against the wind for better control while fishing.

Good question. Always keep them at max psi 65 lbs

I did it today for the first time after years of owning various single axle trailers. Driver side tire is wearing on the inside and passenger side is wearing on the outside. Bearings are good and torque to spec so must be in the spindle itself. The other problem is I couldn't do this in the garage as this would change the direction of the steel belted radial. Had to remove the wheels and have the the tires put on opposite wheels to keep the direction the same. Yes, I've heard it said many times to never reverse the direction of a steel belted radial.......'ole wives tale ?

That's the problem. Crappie are more vulnerable to FFS because they are a schooling fish. A buddy of mine is a diehard crappie fisherman and uses FFS and will sit on an area until they completely quit biting. The other issue is, crappie usually end up in the frying pan. I eat fish too but in moderation.

UnImaginable human behavior, I can't relate.

Jackall flickShake Spinnerbait Jig

The lakes I fish are well populated with channel cats and they frequently hit what bass do, especially scented soft plastics. I grab the net thinking big bass but the continual digging eventually gives it away. 20# flat was a serious fight.

Getting a good night's rest and allowing plenty of time in the morning has eliminated any urge for #2 on the water, have never had an emergency thankfully. Never thought twice about peeing off the bow.

Nothing like a beautiful sunset after a thrilling day of fishing....... great post.

Good news, Thanks for excepting the position.

Only have two. 1. PFD must be worn when the big motor is running. 2. No alcohol

Most are recessed today and aids in comfort and control.

Sam, Praying that you'll have a successful recovery and start slaying the bass like never before.

Was fishing a remote lake in WV several weeks ago, extremely clear water. The day was relatively slow for fishing, bluebird skies. As I was working my way back to the ramp, monstrous boulders suddenly appeared in 10-15 feet of water. Threw a wacky rig on a 1/16 head and landed 3 bass in a matter of minutes. Boulders are something bass can cling to.

I fished a private lake some years back where the owner required barbless hooks. I made pretty quick work using a vice and flat file.

Tennessee got homer happy. Congrats 👏